Your driver is up to date - if you have a problem with your driver, you can try to re-install the old version as below. *: 2K=Windows 2000, 2K3= Windows 2003, XP= Windows XP, VISTA = Windows Vista, WIN7 = Windows 7ĢK, XP, 2K3, VISTA, WIN7, WIN8, WIN81, WIN10/32bits Watch this video to see how it works - click here If your driver isn't working, use the driver having the same OEM with the your laptop/desktop brand name. If you are looking for an update, pickup the latest one. With the different devices, they can have the same driver, it's because they all use the same chip manufacturer. Plan ahead even on a good disk, it will take a while.Īlso, check your BIOS and make sure you have the parallel port set to EPP mode.Below is a list of drivers that may be suitable for your device. If you hear a bunch of clicking and see errors all over the place, the disk is probably junk. If you want to wipe and write to a zip disk in Linux format, it's a good idea to format it something like this ( mke2fs -c -c -L ZIP -m 0 /dev/sdd) to be sure you check for bad blocks. Oct 15 01:06:11 fedora64 kernel: Attached scsi removable disk sdd at scsi7, channel 0, id 6, lun 0Since I formatted most of my zip disk like they were floppies, there is no partition table so something like /dev/sdd1 wouldn't work. Oct 15 01:06:11 fedora64 kernel: sdd: unknown partition table ![]() Oct 15 01:06:11 fedora64 kernel: sdd: assuming drive cache: write through Oct 15 01:06:11 fedora64 kernel: sdd: cache data unavailable Oct 15 01:06:11 fedora64 kernel: sdd: Write Protect is off Oct 15 01:06:11 fedora64 kernel: Type: Direct-Access ANSI SCSI revision: 02 Oct 15 01:06:11 fedora64 kernel: Vendor: IOMEGA Model: ZIP 100 Rev: C.18 Oct 15 01:06:11 fedora64 kernel: scsi7 : Iomega VPI0 (ppa) interface Oct 15 01:06:11 fedora64 kernel: ppa: Communication established with ID 6 using EPP 32 bit Oct 15 01:06:11 fedora64 kernel: ppa: Found device at ID 6, Attempting to use EPP 32 bit The 2.0.36 gives you a clue how long its been since I've used my zip drives! 8-)Ĭode: Oct 15 01:06:11 fedora64 kernel: ppa: Version 2.07 (for Linux 2.4.x) sbin/modprobe /lib/modules/2.0.36/scsi/ppa.o 0x278,0Įcho "To format: mkfs -t ext2 /dev/sda4 98288"Įcho "To mount: mount -t ext2 /dev/sda4 /mnt/zipdrv I put a bash script in my home account (I was the only one to use the zip) which had the folowing lines: The value 98288 was reported by the fsck program. After modprobe is run then either the mount command is executed to mount the disk in the drive, or that disk is replaced with an unformatted disk and the following command is run: ![]() Then you had to be sure a disk was in the drive before doing a modprobe, which will allow modprobe to get the correct size from the hardware. Mine was a parallel one and I had to add the following line to nf:Īppend="ppa=0X278,0" prior to any device stanza, and then run /bin/sbin/lilo as root to update the boot loader. Being a new emachine I'm assuming your parallel port is a bi-directional one isn't it? Is your Zip-100 for a parallel port or is it an ATAPI version? Sorry you didn't get your Zip-100 to work, Mister-Ed. Thanks in advance for any help you can share with me. Please post your replies to this forum so that others may benefit too. ![]() There is media in the drive.Īny ideas of where to look or what to do? Immediately I get the message "mount: No Media Found". * Tried to mount the zip drive: " mount /mnt/zip " * Added the following line to /etc/fstab: " /dev/sda4 /mnt/zip vfat noauto,rw,user,nosuid,sync 0 0 " * Created my mount point: " mkdir /mnt/zip " * Added the following line to /etc/rc.d/rc.local: " /sbin/modprobe ppa " All of the following was done as the root user. The rest came from old RedHat postings and from The Linux Doc Project. ![]() Most of the instructions I followed came from this forum. * I did not attempt any system configuration except what was done during installation process. IomegaWare software does NOT work with Windows 7, so features supplied by IomegaWare will not be available. * Installed a fresh Fedora Core 2 from CD's, no updates to an existing installation. Iomega's site says the following about that qualified for 32-bit Windows 7: 'Zip Drives: Zip 100MB, 250MB or 750MB USB, ATAPI, FireWire or SCSI drives should work with native Windows 7 drivers. The mount command complains "No Media Found" although I know it is there and the drive is properly connected to the system. I'm having a problem getting a parallel port Zip 100 drive to mount. Being a newcomer to Fedora Core, I currently seek good sources of technical information and assistance.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |